New Copy Block Topic Module, Tuesday, April 09, 2024, 3:25:19:46 am

Sort

In Store

Speed

Price

Customer Rating

Online Savings

Availability

Sold By

New Sort & Filter on Topic Page Module, Monday, January 15, 2024, 3:08:36:58 pm

Best Match

Price: low to high

Price: high to low

Tomorrow

2 days

Anytime

Home Improvement

Jewellery & Watches

4 - 5 Stars

3 - 3.9 Stars

Reduced Price

Online

Walmart

Marketplace sellers fulfilled by Walmart

Marketplace sellers

Jack Post Screw and Nut Assembly Mitek Assembled Product Length: 6.25" Assembled Product Height: 2.5" Assembled Product Width: 2.5" . Plate size: 2.5" x 2.5" • Bolt length: 6.25"

Jack Post Screw and Nut Assembly

Jack Post Cross Pin

3-1/2" x 6" Jack Post Top and Bottom Plate Mitek Assembled Product Length: 3.5" Assembled Product Width: 6" . Top Plate

3-1/2" x 6" Jack Post Top and Bottom Plate

6" x 6" Adjustable Post Base Mitek Assembled Product Length: 6" Assembled Product Width: 6" . Height Adjustable Post Base Allows height adjusents of post after installation A maximum height adjusent of 4" can be achieved with this product Adjusents may be required if original installation is not exact, if there is a greater slope on a deck than estimated, or if there is heaving or sinking of the post beyond the initial installation Embed in concrete a minimum of 6" Useful for reducing moisture damage Materials: 16 gauge tube 12 gauge steel U- bracket Finish: Hot-dip galvanized **NOTE** Not recommended for fence posts or other unrestrained (not fixed, nor fastened at top) applications" these anchors are not designed to resist overturning (moment) loads

6" x 6" Adjustable Post Base

5" x 8" Mending Plate - 20 Gauge Mitek Assembled Product Length: 7.81" Assembled Product Width: 4.19" . Prong Mending Plate • With straight prongs • Used to join flat surfaces of two or more wood members • Not intended for structural use • 22 steel gauge • 4-3/16" W x 7-13/16" L

5" x 8" Mending Plate - 20 Gauge

36" - 60" Steel Jack Post Mitek This adjustable support column may be used to support carport roofs and beams carrying loads not more than two wood frame floors, where the length of joists carried by such beams does not exceed 16' and a live load on any floor does not exceed 50 lbs/ft2. Adjusts 36"-60" with working stress 8555 lbs and factored resistance 12319 lbs. Conforms to CAN/CGSB-7.2-94 and is made from 3 gauge steel plates (3-1/2? x 6?); 12 gauge outer tube (2-3/4? O.D); and 11 gauge inner tube (2-1/2? O.D.) in a grey primer finish. To install elevate top tubing to approximate height and insert locking pin., rotate jack screw to desired height, then fasten top plate in position. Ensure top and bottom plates are properly fastened to supported beam members and properly aligned to the supporting base footing and always ensure product is installed 90 degrees to beam and footing.

36" - 60" Steel Jack Post

7/8" x 6-1/2" 22 Gauge Galvanized Brick Tie MITEK Colour Family: GREY Gauge: 22 Size: 0.88" X 6.5" Assembled Product Length: 6.5" Assembled Product Width: 0.88" . Meets prescriptive requirement of CSA A3704-04 for corrugated strip ties • Used to secure brick or rock veneer to wood frame walls • 22 gauge • 7/8" x 6-1/2"

7/8" x 6-1/2" 22 Gauge Galvanized Brick Tie

4" x 6" Nail Joiner Plate Mitek Assembled Product Length: 6" Assembled Product Width: 3.19" . Mending Plate • Prong plates with angled, hammer in prongs • Used to join flat surfaces of two or more wood members • Not intended for structural use • 18 gauge • 3-3/16" W x 6" L

MiTek(8)

Your data, your choice